Motorola Edge Back Cover Replacement

Geschrieben von: Jennifer Berg
  • Kommentare: 2
Motorola Edge Back Cover Replacement

Schwierigkeitsgrad

Moderate

Schritte

7

Zeitaufwand

10 - 25 Minuten

Einleitung

Follow this guide to remove and replace the back cover on a Motorola Edge.

  1. 4FnCQwFMkCAXZ1Bv

    • Completely power off your phone before you begin.

    • Heat an iOpener, then apply it along the bottom edge of the back cover for two minutes.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone because the display and internal battery are both susceptible to heat damage.

    I am having no luck removing the back cover on Moto edge. Can apply heat for more than 2 minutes?

    John Wright -

    You may! Heating beyond two minutes won't hurt your device; the iOpener doesn't get hot enough to do that. Apply the iOpener as long and as much as you need to loosen the adhesive.

    Alex Diaz-Kokaisl -

  2. AJvC56xCf3DLgIGM
    AJvC56xCf3DLgIGM
    3HmjeAx2fHi5ho5W
    WZZQ5vre54dPOoYO

    • Apply a suction cup to the back of the phone, as close to the center of the bottom edge as possible.

    • Pull up on the suction cup with strong, steady force to create a gap between the back cover and the frame.

    • Depending on the age of your phone, this may be difficult. If you're having trouble, apply more heat to the edge and try again.

    • Insert an opening pick into the gap.

  3. 134K3gAaQd61AE2Z
    134K3gAaQd61AE2Z
    qtvhXbE1iNY2tVNU
    M3XV6iS5GGFsQKsh

    • Slide the pick back and forth along the bottom edge to slice through the adhesive.

    • Leave the pick in to prevent the adhesive from resealing.

  4. GVKaPvArIykYynBo

    • Apply a heated iOpener to the back cover's right edge for two minutes.

  5. OuSUYlhHlVtqLO2Q
    OuSUYlhHlVtqLO2Q
    cf14Sni2BatKPMPb
    PC2SdtEGWCikGCWS

    • Rotate the opening pick around the bottom-right corner of the phone.

  6. yMD46IcUqwFO4tOA
    yMD46IcUqwFO4tOA
    URBcrAgUIiQIcwhA
    dWvkBMaTxV2ih3di

    • Insert a new opening pick into the gap you just created.

    • Slide the pick along the right edge of the phone to separate the adhesive.

    • Repeat the heating, slicing, and leaving opening picks for the remaining edges of the device.

  7. xUlG23riKM3otWY4
    xUlG23riKM3otWY4
    uRUwx6YfQuPycAkJ
    ecTIFopZkXm5LvDd

    • Remove the back cover, taking care not to damage the components inside the phone.

Abschluss

To reassemble your device, follow these instructions in reverse order.

For optimal performance, calibrate your newly installed battery after completing this guide.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers Community for help.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before you install it.

Tinte & Feder

Jennifer Berg

Mitglied seit: 21/03/22

2415 Reputation

0 Kommentare