Nintendo Switch Pro Controller Rumble Modules Replacement

Geschrieben von: Jean Galindez

Kommentare: 10

Nintendo Switch Pro Controller Rumble Modules Replacement

Schwierigkeitsgrad

Difficult

Schritte

Zeitaufwand

1 Stunde

Einleitung

This guide is used for the replacement of the Rumble Modules on your Nintendo Switch Pro Controller. Take precaution when completing this guide because it involves the removal of a lithium-ion battery. If the battery is swollen, check out this resource on how to dispose of a swollen battery. To complete this guide correctly you must complete steps eight and nine with caution so as to not damage the white ribbon. In addition, you must be able to solder, so if you do not know how to solder, check out this resource on how to solder. Be careful when removing the plastic pieces and the internal circuit board of the controller so as to not damage the components.

Werkzeuge

Ersatzteile

Nintendo Switch Pro Controller Rumble Module

Schritt 1

Flip the controller over so the model stickers face the ceiling.
Use a JIS #00 screwdriver to remove the two black 8.4 mm screws that secure the handles, located at the ends of the handles.

Be carefull, these screws are super easy to strip even with the right tools.

Lukas Eberharter -

I tried editing these instructions after I had trouble with stripping screws, but it doesn't seem to take. The issue is that these are JIS and not Phillips screws. They are VERY similar looking but a Phillips head screwdriver will strip the screws.

Isaac Webb -

I tried using a Philips #00 screwdriver but it didn’t work

vincent ingrassia -

Schritt 2

Carefully remove the handle covers by pulling them away from the main body.

Schritt 3

Use a JIS #00 screwdriver to remove the four silver 6.8 mm screws that secure the clear back plastic cover.

Schritt 4

Carefully pry away the clear plastic cover using your fingernail.

Schritt 5

Remove the clear plastic cover.

Schritt 6

Remove the lithium-ion battery by using a fingernail or plastic opening tool to pry it up on the left side.
Only a small amount of force is needed.

Schritt 7

Use a Phillips screwdriver to remove the five 5mm-long screws from the back of the controller.

the 2 screws up at the top are unreachable with the standard fixit kit just a heads up

drew - 06/02/21

Seconded. the screws are located too deep below the plastic slot, and the bit holding bulge is too wide for the small aperture (similarly with the flexible extension). the bit length is too shallow to reach.

An alternative driver with a much narrower & longer shaft is required, which will likely not come with interchangeable bits.

Douglas Selby - 05/03/21

I would say it is possible to reach the top left screw, just not the top right - there is a gap in the top left that allows you to slightly bend the standard driver outward to turn it while still making adequate contact.

El_Mechacontext -

An update: I was actually able to remove the top right one in a really hacky way - inserting the Phillips #0 bit into the #4 hex bit, and then using that in the standard driver. This added just enough length to successfully reach and make full contact with the screw!

El_Mechacontext -

Using the #4 hex bit as an extension was the exact "hack" I needed to get rid of the drift finally. Thank you. You're a lifesaver.

Das #4 Hex Bit als Verlängerung für das Kreuzschlitz Bit zu nutzen ist zwar etwas eng, aber es erspart einem wirklich einen zusätzlichen Schraubendreher.

Techn0magier -

Schritt 8

Delicately take off the plastic cover from the controller.
Do not completely remove the front cover just yet, as it is still attached to the motherboard via a white ribbon cable.

Didn't realize there is adhesive holding the front cover onto the unit. It's located inside of the handles. Just a bit of force there helped, just be careful of the cable.

Roger Perez -

Schritt 9

Use the tip of an opening pick to open the black flap of the ZIF connector by pushing it upwards.

Schritt 10

Use your fingers or a pair of blunt nose tweezers to disconnect the interconnect cable from its connector.

Schritt 11

Remove the front case.

Schritt 12

With light force pull the two joystick caps off of the controller.

Schritt 13

Insert the tip of a spudger from the back into the hole on the right controller handle.
Push the spudger through the hole to loosen the adhesive which is holding rumble modules in their places.

Schritt 14

Insert the tip of a spudger from the back into the hole on the left controller handle.
Push the spudger through the hole to loosen the adhesive which is holding rumble modules in their places.