OnePlus Nord 2 5G Daughterboard Cover Removal

Geschrieben von: Dominik Schnabelrauch
  • Kommentare: 0
OnePlus Nord 2 5G Daughterboard Cover Removal

Schwierigkeitsgrad

Moderate

Schritte

18

Zeitaufwand

30 - 45 Minuten

Einleitung

This is a prerequisite-only guide! This guide is part of another procedure and is not meant to be used alone.

Use this guide to remove the daughterboard cover in the OnePlus Nord 2 5G.

  1. QKtCRoMOdUXmDBHT

    • Prepare an iOpener and apply it to the rear glass for at least three minutes to loosen the adhesive underneath.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

  2. bgbQGZdPwSJvpjwQ
    bgbQGZdPwSJvpjwQ
    16XlatOmPjY6ZIO6
    HeUofpxwddv2D35A

    • Due to its surface, no suction tool will hold onto the phone's rear glass. A thin slicing tool is required to create a gap between the rear glass and the midframe.

    • Insert an iFlex into the seam between the rear glass and the midframe at the bottom edge of the phone to create a gap. This may require some force.

    • Leave the iFlex in place to prevent the adhesive from resealing.

  3. SkGsiX3GrRFVLNOd
    SkGsiX3GrRFVLNOd
    P5KNLG2okCXo1Dku
    vdwpOuHCEMqGYdCu

    • Insert an opening pick into the gap you created with the iFlex.

    • Remove the iFlex.

  4. wjcSqJwZVfym2srg
    wjcSqJwZVfym2srg
    icUePqDHShPL1yOt

    • Slide the opening pick to the bottom right corner to slice the adhesive.

    • Leave the opening pick in place to prevent the adhesive from resealing.

  5. NtqBL6CEoqvc2kCi
    NtqBL6CEoqvc2kCi
    sqtYXqD11ZTJGpAR

    • Insert a second opening pick at the bottom right corner of your phone.

    • Slide the opening pick to the bottom left corner to slice the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

  6. DE6qOhQIDe2kRvyU
    DE6qOhQIDe2kRvyU
    62DlLRAjUloDYmJJ
    GI2MM3HQs5XRsI6x

    • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener to reheat it.

    • Insert a third opening pick at the bottom left corner of your phone.

    • Slide the opening pick along the left edge of your phone to slice the adhesive.

    • Leave the opening pick in the top left corner to prevent the adhesive from resealing.

  7. 2JscQLrdqNEiBWLx
    2JscQLrdqNEiBWLx
    HZwLDXITLLHgkGyn

    • Insert a fourth opening pick underneath the top left corner of the rear glass.

    • Slide the opening pick along the top edge to slice the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

  8. VpUI6Vbo2WTpNIMD
    VpUI6Vbo2WTpNIMD
    saOOVOuHwpTVMYIB
    yqoMRLRYHiVHoROI

    • Insert a fifth opening pick underneath the top right corner.

    • Slide the opening pick along the right edge of the back cover to slice the remaining adhesive.

  9. M6FERYgED3Ir6dbp
    M6FERYgED3Ir6dbp
    TMMyPtrgUOQgldmg

    • Remove the back cover.

    • Secure the new back cover with pre-cut adhesive or double-sided adhesive tape. After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond—a stack of heavy books works well.

  10. MEGHWsxMfxGWjGjj
    MEGHWsxMfxGWjGjj
    B3cRooPUEDGwCdrX

    • Use a pair of tweezers to remove the metal bracket covering the flash assembly connector.

  11. vQYUak5ngNoFqIWC
    vQYUak5ngNoFqIWC
    JvPIEhJQYhmBBjPT

    • Use the point of a spudger to disconnect the flash assembly cable by prying the connector straight up from its socket.

  12. lNM2LLtJ1CLsPvri

    • Use a Phillips screwdriver to remove the nine 3.8 mm-long screws securing the motherboard cover.

  13. AMs3h22Vsrrne3Kd
    AMs3h22Vsrrne3Kd
    HVVuEISpiUswwEWW
    XqKmRSI2VKwppHCO

    • The motherboard cover is held in place by plastic clips.

    • Insert an opening pick underneath the bottom right edge of the motherboard cover.

    • Twist the opening pick sideways release the plastic clips and to pry up the motherboard cover.

  14. DFXLadAs1B6hNXZ4
    DFXLadAs1B6hNXZ4
    AsbwN2CTInQFermE

    • Remove the motherboard cover.

  15. JPRSARre2iOhpXTI
    JPRSARre2iOhpXTI
    Z3gnpPwIPTmPkWKc

    • Use a spudger to disconnect the battery cable by prying the connector straight up from its socket.

  16. OaprH1ccicIFsn1q

    • Removing the daughterboard cover isn't mandatory to replace the battery. However, doing so reduces the risk of damaging surrounding components.

    • Use a Phillips screwdriver to remove the six 3.8 mm-long screws securing the daugtherboard cover.

  17. aBTdXOcCXoVDZmhF
    aBTdXOcCXoVDZmhF
    XFpY5FpBhZngSknU

    • Insert the point of a spudger underneath the top right edge of the daughterboard cover.

    • Pry upwards to loosen the daughterboard cover.

    • Don't try to remove the daughterboard cover all the way yet. It's still adhered to the loudspeaker.

  18. Ikedn1o1vDsdPOLm
    Ikedn1o1vDsdPOLm
    c3ZtbEBNZaMLPPqX
    2tJYS25PQVUkZu3W

    • Fold the daughterboard cover to the left like you would open the front cover of a book.

    • Carefully peel the black tape off of the loudspeaker.

    • Remove the daughterboard cover.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our OnePlus Nord 2 5G answers community for help.

Tinte & Feder

Dominik Schnabelrauch

Mitglied seit: 23/11/16

167866 Reputation

0 Kommentare