PowerBook G3 Pismo Hard Drive Replacement

Geschrieben von: iRobot
  • Kommentare: 2
PowerBook G3 Pismo Hard Drive Replacement

Schwierigkeitsgrad

Easy

Schritte

14

Zeitaufwand

Keine Schätzung

Einleitung

How to remove the hard drive, along with its cable and bracket from your computer.

  1. 1LvSAqP1lHsbjn2A

    • Turn the keyboard locking screw so that it is parallel to the space bar.

    • Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.

    • Lift the keyboard out by pulling it up and away from you. Rest the keyboard, face down, on top of the track pad.

  2. OOxGGCT1cYLJrrIV

    • Pull the keyboard ribbon straight up from the logic board. Place the keyboard aside.

    • The connector may be tight. Gently rock the connector from side to side while pulling directly upward to free it. You can use this technique on many of the cards and cables you'll be disconnecting.

    • Make sure you have removed the laptop battery and CD/DVD modules from the expansion bays before proceeding.

  3. xXLqar4m52POFPI1

    • Your laptop should look approximately like this.

  4. RjbEC5iCcCOOfLbZ

    • Remove the two silver Phillips #1 screws that attach the heat shield to the internal metal framework.

    • Lift the heat shield up and pull it toward you.

    On my M7572, these are T9s not Philips.

    Rufleyboy -

  5. 1RNBn42uEKZlcVLO

    • Your laptop should look approximately like this.

  6. lCLeEKFXCoVRjQ1D

    • Skip this step if your computer does not have an Airport card installed.

    • Firmly grasp the plastic tab attached to the Airport card and pull up and then to the right.

    • The Airport card is still attached to the antenna cable, so don't just yank it out of the slot.

    On mine, the airport card had been put it with the orange ribbon OVER the top, so had to unplug the righthand connector and then plug it back in after (see pic for Step 8)

    Rufleyboy -

  7. hPnOXJZEDBBTHUAg

    • Disconnect the antenna cable from the Airport card.

  8. JkWpBVo56At4Ejxu

    • Remove the long silver Phillips #1 screw from the heat sink.

    • Remove the two T8 Torx screws that attach the heat sink to the processor.

  9. BstZaZL2ZCaSSDH1

    • Lift the heat sink up from the left side and pull it out.

    • If you need to mount the heat sink back into the laptop, we have a thermal paste guide that makes replacing the thermal compound easy.

  10. iABbhXu1DLVqcHkA

    • Grasp the plastic tab on the processor's right side and pull it directly up.

    • Some processors may be missing the plastic pull tab. In this case, we suggest using a non-metal tool to gently pry up the processor. Slip the tool's thin edge under the front right corner of the processor and carefully pry it up.

  11. qfUOSMWlUvnZYM3X

    • Your laptop should look approximately like this.

  12. rKxx12YX14KG6iys

    • Grasp the orange cable at the left end of the hard drive and disconnect it from the logic board.

    • Try to grasp the cable on the plastic connector rather than on the flexible cable section.

  13. fsgxpURjjPVLNscA

    • Grasp the plastic tab and pull the hard drive up and to the left, making sure that the metal bracket doesn't catch on the black plastic casing.

  14. hgXdDTvrvvjoVEdD

    • Your laptop should look approximately like this.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

iRobot

Mitglied seit: 25/09/09

0 Reputation

0 Kommentare