Einleitung

Wenn du ein falsches Bit an deinem Schrauber wählst kann das genau den Unterschiede zwischen Freude oder Frust machen. Diese kleine Anleitung zeigt dir, wie du das richtige Bit für deine Schrauben identifizieren kannst und damit fürchterlich zugerichtete Schrauben vermeidest.

Wenn du danach immer noch Schwierigkeiten hast, dann schaue dir diese tolle Anleitung an.

  1. TQokhGKRPl4hhgJl
    TQokhGKRPl4hhgJl
    i5ET5UqEfJQlYwgh
    • Die Schraubenbits an deinem iFixit Kit haben kleine Gravuren an denen du sie identifizieren kannst. Die Gravuren bestehen aus Buchstaben für den Typ und Zahlen für die Größe. Hier einige Beispiele:

    • PH2 - (Phillipps Nr.2). Das ist ein Bit für große Kreuzschlitzschrauben.

    • PH0 - (Phillipps Nr.0). Das ist ein Bit für mittlere Kreuzschlitzschrauben.

    • PH000 - (Phillipps Nr.000). Das ist ein Bit für kleine Kreuzschlitzschrauben.

    • Wähle die Bitgröße so, dass das Bit vollständig in den Schraubenkopf passt. Ein Bit, dessen Größe nicht angepasst ist, wird den Schraubenkopf beschädigen.

  2. xnDnSAGsuCvjIaUs
    xnDnSAGsuCvjIaUs
    LbRmaPUZPvDApCMR
    • Wenn du dir den Kopf darüber zerbrichst, wie du das richtige Bit feststellen kannst, dann schaue mal auf diese Referenzliste.

    • Das ist die Form des Schraubenkopfs, dazu die richtige Bezeichnung. Flathead bedeutet Flach- oder Schlitzschraubenkopf. Phillipps Schrauben werden auf Deutsch meistens einfach Kreuzschlitzschrauben genannt.

    • Die Bitgröße

    • Wenn du eine Anleitung erstellst und du findest nicht die genau richtige Bezeichnung an deinem Bit, dann benutze einfach den ausgeschriebenen Namen. (Beispiel: "Benutze ein 1,5 mm Schlitzkopfbit um die beiden 5mm Gehäuseschrauben herauszudrehen.")

  3. COuDqcUJiEFVu2Xi
    COuDqcUJiEFVu2Xi
    RXLMVlVECkChrrEp
    • Bits mit der Bezeichnung "J" und "PH" werden oft als gleich angesehen. Lass dich nicht vom scheinbar gleichen Aussehen täuschen - sie sind verschieden!

    • Phillipps (PH) (oder deutsch meistens Kreuzschlitzschrauben) haben eine solche Form, dass die Bits herauskommen, wenn zu stark gedreht wird. Dadurch werden die Schraubenköpfe nicht so leicht beschädigt.

    • Japanische Industriestandardschrauben (J) sind auch Schrauben mit einem Kreuzschlitz. Sie haben aber nicht die runden Ecken, sondern sind direkt rechtwinklig geschnitten, so dass die Bits nicht herauskommen, wenn zu stark gedreht wird.

    • J (oder JIS) und PH (Phillips bzw. Kreuzschlitz-) Bits sind nicht immer austauschbar. Am Bild siehst du, dass sie nicht völlig gleich sind!

    which is which? why not tag each with a label?

    Jay Heldman -

    Japanese Industrial Standard (J) screws do not provide a cam-out option, and have 90 degree corners

    Oscar -

    Does a PH bit also fit into a J screw?

    Alberto -

    Hiya, Alberto! Great question. Smaller screws found in electronics aren’t particularly durable, and using a Phillips screwdriver on a Japanese Industrial Standard screw head (or vice versa) can lead to some pretty major problems. I highly recommend using the proper screwdriver or bit to avoid stripping screws.

    Richard Suovanen -

    Which one should I get in America for iPhone and laptop type repairs , PH or J?

    eliyahu Stein -

    According to JIS and ISO standard, both recess dimension seem to be the same, having a rounded corner between two flats. I think, the recess without rounded corners (as right drawing) is a recess of CIPA (older JCIS) standard. According to CIPA, the edge between two flats is R0.06mm rounded shape, which seems to be neary sharp edge. Anyway, CIPA is a Japanese Standard and used mainly for the screws of Japanese electrical instruments.

    gk3lglink -

    I have two Phillips heads, one is labelled PH.2, the other labeled SH.0.

    The second one has a very snub nose, which is what I need for the screws I need to work on. The more pointed PH one is too loose as the point doesn't allow it to fully seat into the screw head.

    A seemingly identical snub-nosed one from another set is labelled: CR-V3#, and another seeming clone as ACR-2..

    I'm having a bit of confusion on how to buy another screw bit like I need.

    Guthrie -

Richard Suovanen

Mitglied seit: 07/02/17

27640 Reputation

13 Kommentare

Excellent guide. could not figure out the difference by looking.

Lawrence Steinheuer-Turner -

It would be clearer if the displayed drawing of each bit actually said J-bit or PH-bit, and because both have 90 degree corners, maybe change the J-bit description to “have 90 degree square inside corners“ and include in the PH description “have 90 degree rounded inside corners.

Otherwise, with interpretation, your article helped me.

Phil -

what size hex shaft do these smaller bits have?. i have an electric precision screw driver, for electronics. i go through the PH1 bits very quickly. i can NOT find them for sale anywhere on earth. does anybody know where to purchase these things?? and/or tell me how i should word the query. all im getting is 1/4 hex shaft results. very frustrating

brett everett -

In the picture on the top of the page the bits with a 90° corner are marked as Phillips heads, the ones with the rounded corners are markes as JIS heads. But it seems to be the other way, as mentioned in Step 3 of this instruction, and also according to other pages like Kreuzschlitzschraubendreher #000

Andreas Brunner -

Sharp eye, Andreas! Thanks for catching that. We’ve updated the image at the top of the guide with the correct labels.

Marty Rippens -

i have just bought an ifixit kit, has some ph and j bits. I’ve looked at them under a microscope, compared angles, tried them on screws... i have found no difference whatsoever, they seem to be identical. What gives?

Victor Titov -

Hi @deepsoic, that’s a pretty interesting find you’ve made! Send an email over to our customer service team at support@ifixit.com and they’ll help you get this issue sorted.

Amber Taus -

The label indicating the drivers on the Mako 64-bit driver set is almost impossible to read (embossed black-on-black). You can print a better one from the diagram on the catalog page. See https://twitter.com/isonno/status/146455...

isonno -

I got this set as a gift and I’m very disappointed it doesn’t include larger Phillips head bits. The largest in this set is too small for a lot of the screwheads on my electronics, especially since I’ve never seen some of these screwheads in my entire life. Do you have any larger Phillips bits for sale?

Matt -

Hi, Matt! Sorry to hear that your current kit doesn't meet your needs. We do have a larger 1/4" driver kit that goes up to PH #3 (Mahi).

Richard Suovanen -

Where does pozidriv (PZ) fit in. I know its not Phillips, so seem to be another bit type?

Alan -

Probeer de volgende link eens: https://shop4fasteners.co.uk/blog/pozidr...

Misschien wordt het dan duidelijker.

Toon Konings -

Il manque (cruellement) l'empreinte POZIDRIV souvent source de confusion.

Roland29 -