MacBook Pro 13" Two Thunderbolt Ports Late 2020 Antenna Bar Assembly Replacement

Written By: Carsten Frauenheim
  • Comments: 9
MacBook Pro 13" Two Thunderbolt Ports Late 2020 Antenna Bar Assembly Replacement

Difficulty

Moderate

Steps

28

Time Required

1 - 2 hours

Introduction

Use this guide to replace the antenna bar assembly of your MacBook Pro 13" Late 2020.

For your safety, drain your MacBook Pro’s battery to 25% charge or less before you begin.

Some photos in this guide are from a different model and may contain slight visual discrepancies, but they won't affect the guide procedure.

  1. Q1wvDeNfY4uOiyKt

    • Before starting this procedure, you should disable your Mac's Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.

    • If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you're inside.

    • Completely power off and unplug your MacBook before you start. Close the display and flip the entire laptop upside-down.

    • Use a P5 Pentalobe driver to remove the six screws securing the lower case:

    • Two 6.8 mm screws

    • Two 5.3 mm screws

    • Two 3.4 mm screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

    I use a empty egg carton to place screws in in the order of removal from computer

    robert -

  2. HNcAU1OxShTMSVcH
    HNcAU1OxShTMSVcH
    RV2F6vZPN4bDRjpF

    • Apply a suction handle to the lower case near the front-center area of the MacBook Pro.

    • Lift the suction handle to create a slight separation between the lower case and the chassis.

  3. fBkwTalJQNyTPwSp
    fBkwTalJQNyTPwSp
    6KuUDjvctvBQpU6F
    aKYwtXFASPKBPNFN

    • Insert one corner of an opening pick into the space between the lower case and the chassis.

    • Slide the opening pick around the nearest corner and halfway up the side of the case.

    • This releases the first of the hidden clips securing the lower case to the chassis. You should feel and hear the clip pop free.

  4. R2wEm6jobOXjQloV
    R2wEm6jobOXjQloV
    ZMvhcRVcNbRarUlR
    pIAj3iNjoHmrl5eD

    • Repeat the previous step on the opposite side, sliding your opening pick under the lower case and up the side to pop the second clip free.

  5. CnvC3ADHsHWCSorW
    CnvC3ADHsHWCSorW
    ZNEgaHfCsrAb11eC
    r5umcQAM1T4f4AXQ

    • Insert your opening pick once again under the front edge of the lower case, near one of the two centermost screw holes.

    • Give the pick a firm twist to pop free the third clip securing the lower case to the chassis.

    • Repeat this procedure near the other of the two centermost screw holes, popping the fourth clip free.

  6. Be4XcBdPlUxGlirO
    Be4XcBdPlUxGlirO
    4IVGUAoP6imcUgqT
    LKAkvpHxVvOHEU2S

    • Pull the lower case firmly towards the front of the MacBook (away from the hinge area) to separate the last of the clips securing the lower case.

    • It may help to pull first at one corner, then the other.

    • Pull to the side—not up.

    • This may require a lot of force.

    • The edges of the case can be sharp, so grip the sides carefully.

    Be mindful of finger placement as the inside edges of the case are very sharp and may cut you.

    Shane Samuelson -

    literally just cut myself

    Jaiden Daniel Arnett -

    I used the suction cup to pull/slide the lower case from the back clips

    Richard Dunn -

  7. gBJPsmHQnCcGuQGP

    • Remove the lower case.

    • To reinstall the lower case:

    • Set it in place and align the sliding clips near the display hinge. Press down and slide the cover toward the hinge. It should stop sliding as the clips engage.

    • When the sliding clips are fully engaged and the lower case looks correctly aligned, press down firmly on the lower case to engage the four hidden clips underneath. You should feel and hear them snap into place.

  8. 4fxcSwlNeTWUfaNc
    4fxcSwlNeTWUfaNc
    L1j1MRZCosVLrlH2

    • Carefully peel up the large piece of tape covering the battery connector, on the edge of the logic board nearest the battery.

    • Remove the tape.

  9. X1eMBkm2fAmXKLZt
    X1eMBkm2fAmXKLZt
    5iCBA1UK3Y1VGBUd

    • Gently peel back the small piece of tape covering the battery board data cable connector.

    • The tape is integrated into the ribbon cable and will not detach completely. Simply peel it back enough to access the connector.

  10. m2ZMQiqkPMUNCckG
    m2ZMQiqkPMUNCckG
    ySdWyeoNwF1mIGE1

    • Use the tip of a spudger to flip up the small black locking tab securing the cable in its connector.

    • Locking tabs on ZIF connectors are fragile, so be gentle when using the tip of the spudger.

  11. ssX4BEtvDiq3BC2S
    ssX4BEtvDiq3BC2S
    AgTwyOsjGHYBeqWy

    • Disconnect the battery board data cable by sliding it out from its socket.

    • Slide parallel to the logic board, in the direction of the cable.

  12. 2hRujNSkWYa1yBhH

    • Fold the battery board data cable back and out of the way.

    • If you're replacing your battery, you may need to completely remove and transfer this cable to your new battery. Disconnect both ends and carefully remove the cable. During installation, be careful not to install it upside-down or backwards—note the orientation in the photos.

  13. lSaMKOjmtmpvMSgC
    lSaMKOjmtmpvMSgC
    bLADI3bSOZ4yUiH2

    • Use a T5 Torx driver to remove the 3.7 mm pancake screw securing the battery power connector.

    io ho trovato un Torx T4 invece del T5.

    Stefano Supino -

    Ciao Stefano! Grazie per il commento. Infatti c’è sempre una certa tolleranza fra il cacciavite e la testa delle viti. Quindi è possibile che un cacciavite più grande o più piccolo sia più “comodo” in certi casi. Buona riparazione!

    Claire Miesch -

  14. RVQlOAm2qrSPBPss
    RVQlOAm2qrSPBPss
    NhCLsrVJdF6AhpAy

    • Use a spudger to gently lift the battery power connector, disconnecting the battery.

    • Lift the connector high enough so that it stays separated from its socket. If it accidentally makes contact during the course of your repair, it could damage your MacBook Pro.

    Hello, I have damaged this connector and it is now loose with the logic board. It is possible to replace this connector?

    Thanks

    deejaygav -

  15. EflRAU2rodC1ZAih

    • Remove the four 3.3 mm T3 Torx screws securing the plastic covers on top of the display hinges.

  16. MXhJTZyQJQX1tDps
    MXhJTZyQJQX1tDps
    Ie5qKCtYWhCBPh4N
    f6HLmggFmwYi1N4H

    • Remove both plastic hinge covers.

  17. XCo2duM5jHgBaRHt
    XCo2duM5jHgBaRHt
    XqvyPUM6umKEarMJ

    • Remove the two 3.1 mm T3 Torx screws securing the aluminum cover on top of the main display cable.

    • Remove the cover.

  18. 3assCBIHC6ZENZB4
    3assCBIHC6ZENZB4
    LrPU4my5JEiebdZf

    • Remove the two 1.7 mm T3 Torx screws securing the aluminum cover on top of the display cable flex connector.

    • Remove the cover.

  19. ZicIIukdvKbJA4mk
    ZicIIukdvKbJA4mk
    AChBI1smoF2TRv1a

    • Pry the display board flex cable straight up from its socket to disconnect it from the display board.

  20. lIJFaYEvXThx3dfI
    lIJFaYEvXThx3dfI
    V6raxkOFdOYlo2QG
    G45RY1qjgGqMIhHM

    • Remove the four 1.5 mm T3 Torx screws securing the two aluminum covers on top of the two display cable connectors.

    • Use a pair of tweezers to remove the two aluminum covers.

    You can skip this step if these are included on your replacement screen.

    maccentric -

  21. asTmkESBMJbWaIWu
    asTmkESBMJbWaIWu
    yRO6cRSb5xBripSI

    • Remove the four 3.3 mm T5 Torx screws (two on each side) which secure the antenna cable assembly.

    • Also remove the twelve 1.1 mm P2 pentalobe screws (six on each side).

    • These small screws can strip easily, so make sure your P2 pentalobe driver is in good condition before applying pressure.

  22. nO5JUcQYkYcZwHrq
    nO5JUcQYkYcZwHrq
    oVaXihXWAjIq5eGn

    • Use a pair of tweezers to remove the plastic antenna cable cover.

    • This cover is secured with some light adhesive.

  23. Tlyrfe6j4OVUBWPx
    Tlyrfe6j4OVUBWPx
    3Y5xdL6tFg4FEZDN
    GlZleLdmhyEFtwcq

    • Carefully disconnect the two antenna coax cables by prying them straight up from the logic board.

    • Slide your tweezers or the flat end of your spudger underneath each cable until it's near the socket, and then gently twist or pry up to disconnect it.

  24. vYpFGZxpqmFb1eDJ
    vYpFGZxpqmFb1eDJ
    NfRObSXK6gotGNJ3
    GAK4rIuifJVNbAKU

    • To reconnect each antenna cable, use tweezers to align the connector directly over its socket, and then press down with a spudger so it snaps into place.

  25. NnqjyK3UyE3Li4gn

    • Remove the 3.7 mm T5 Torx screw securing the two antenna coax cables to the main board.

  26. xlULfxdob1BkxXPF
    xlULfxdob1BkxXPF
    BPiysjspLM5ftRBP
    KppbYduwRQdmNCFK

    • Use an opening pick to lever out the antenna cable assembly in the areas shown.

    • Don't slide the opening pick from side to side, because there are two display cables that can be damaged.

  27. LCMLlra3woPG2m3U
    LCMLlra3woPG2m3U
    4dx314fbWTuNK3ik

    • Carefully remove the antenna assembly while simultaneously feeding the antenna cable bundle out from underneath the heat pipe.

  28. 36dmRHOZcCAtHgTB

    • Remove the antenna cable assembly.

    • During reassembly, gently pinch the cable bundle together and guide it under the heat pipe into the correct position on the board. If needed, use your tools to help guide it through, but don't force it.

    Do step 29 before you attempt to remove the wifi

    BRUCEL86 -

Conclusion

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting or search our Answers community for help.

Author

Carsten Frauenheim

Member since: 10/03/20

87825 Reputation

0 comments